Precision machining · Kempton Park, Gauteng

CNC turning, milling & Fanuc programming — true to drawing, first time.

We are a programmer-led machining team making precision turned and milled parts, hydraulic cylinder components and CNC programs for workshops, plants and manufacturers across the East Rand and Gauteng.

  • 15+ years' Fanuc CNC experience
  • First-off approved before every batch
  • One-offs to production runs
A steel rod held in a CNC lathe chuck while a cutting tool turns it to size

What we do

Machining and CNC know-how under one roof

From a single replacement shaft to a batch of hydraulic pistons — or a better program for your own machine.

  • CNC turning

    Shafts, pins, bushes, sleeves, threads and bores turned to drawing on Fanuc-controlled CNC lathes — one-offs to production batches.

  • CNC milling

    Faces, pockets, slots, keyways and drilled or tapped hole patterns, plus second operations on turned parts.

  • Hydraulic cylinder components

    Piston rods, pistons, glands, end caps and clevises machined to the tolerances and finishes hydraulic seals demand.

  • Fanuc CNC programming & optimisation

    G-code and ISO turning programs written from your drawings, and existing programs tuned for shorter cycle times and less waste.

  • Machine setup & troubleshooting

    Full machine setup, first-off approval and fault-finding for workshops when production is stuck or a new job needs proving.

  • Operator support & training

    Practical, on-machine coaching for CNC operators and setters: offsets, setups, drawings and in-process measuring.

Two machined metal components resting on engineering drawings

Why work with us

The people who quote your job are the people who program and set the machines

  • Fanuc specialists

    Advanced Fanuc turning training and many years of day-to-day programming on Fanuc controls.

  • Hydraulic-grade precision

    Long experience making hydraulic cylinder parts, where tolerances and surface finish decide whether a seal holds.

  • Checked, not hoped

    Drawing review up front, an approved first-off, and in-process inspection with calibrated measuring tools.

  • Efficiency built in

    We plan tooling, feeds and speeds properly to keep setup and cycle times down, which keeps the cost of your parts down too.

How it works

From drawing to finished part in four steps

  1. Send your drawing

    A drawing, sketch or photos of a sample, with the material and quantity.

  2. Get a clear quote

    Price, lead time and any questions about the design — in writing.

  3. We program & prove

    We program, set up and measure a first-off before the batch runs.

  4. Inspect & deliver

    Checked throughout and handed over ready to fit.

About us

A small team with deep shop-floor experience

TrueTurn Engineering grew out of more than 15 years spent programming, setting and running CNC lathes and milling machines in a busy precision-engineering production environment — much of it on components for hydraulic cylinder systems.

We know what holds production up because we have spent years fixing it: programs that waste time, setups that drift, drawings that are easy to misread. We bring that experience to every part we make and every workshop we support.

Fanuc trained — Advanced turning Fanuc trained ADVANCED TURNING 15+ years — CNC experience 15+ years CNC EXPERIENCE
A bright machine shop with CNC machines and workbenches

In the shop

Representative workshop photography.

Where we work

Serving the East Rand and greater Gauteng

We are based in Kempton Park, close to OR Tambo and the Isando and Spartan industrial areas. Setup, troubleshooting and training happen at your premises; machining work can be collected and delivered by arrangement.

  • Kempton Park
  • Benoni
  • Boksburg
  • Germiston
  • Edenvale
  • Springs
  • Brakpan
  • Alberton
  • Isando
  • Spartan
  • Johannesburg
  • Midrand
  • Pretoria

Questions

Frequently asked questions

What do you need from us to quote?

A drawing (PDF, DWG/DXF or a clear sketch with dimensions), the material, the quantity and when you need the parts. If you only have a worn or broken sample, send photos and tell us — we will advise whether we can work from it.

Do you take on one-off jobs or only production runs?

Both. We machine single replacement parts for breakdowns as well as repeat batches. For repeat work we keep the proven program and setup notes, so the next batch starts faster.

Which areas do you serve?

We are based in Kempton Park and work with clients across the East Rand and greater Gauteng, including Benoni, Boksburg, Germiston, Edenvale, Johannesburg, Midrand and Pretoria.

Can you help with our own CNC machines?

Yes. We write and optimise Fanuc programs, set up machines, prove first-offs, troubleshoot problems that are holding up production and coach your operators on the machine.

More questions answered

Got a drawing? Get a clear quote.

Send us your drawing, sketch or photos of the part. We will come back with price, lead time and any questions about the design.